HPE2-T37 Using HPE OneView Questions and Answers

RoCE networks require Virtual Connect SE 32Gb FC Modules.

RoCE networks cannot be configured when Virtual Connect modules are used.

RoCE networks are supported only when PVLANs are enabled.

RoCE networks are not supported with HPE BladeSystem

POST

GET

DELETE

PUT

The teaming or bonding driver in the server OS must be configured to enable the LACP and to form the LAG correctly.

The server profile for a given HPE Synergy compute module should be reapplied, then the Compute Module should be rebooted.

Link Aggregation Group functionality should be enabled in advanced properties of the Logical Interconnect.

Ensure that the Link Aggregation Group time-out value matches the server set values.

network purpose can give higher priority for a specific type of traffic

network purpose will impact the traffic only if Virtual Connect modules are used

network purpose will define QoS within Logical Interconnect

network purpose does not affect the behavior of the network

HPE Virtual Connect modules

HPE Apollo XL 170r

Brocade and Cisco SAN Manager

HPE Primera and HPE 3PAR

When combined with IRF, M-LAG will allow you to aggregate ports coming from clustered HPE Synergy Virtual Connect modules.

M-LAG for HPE Synergy can be either single-homed or multi-homed, while for HPE BladeSystem only single-homed.

sFLOW cannot be enabled if M-LAG is configured between HPE Synergy Virtual Connect modules in the same frame.

M-LAG has to be defined manually for HPE BladeSystem, but it is automatically configured for HPE Synergy.

The other networks are not configured with the required Smart Link parameter.

The other networks are not added to the Logical Interconnect Group configuration.

The other networks have Private Network' selected, which hides them from Compute Modules.

The other networks are configured with a purpose other than General or Management.

Compute Module

Storage Array

Master Module

Logical Enclosure

nPartition configuration.

BMC settings.

Complex firmware baseline.

Ethernet connections.

Shrinking a volume

Volume conversion

Remote replication

Growing a volume

A PowerShell script must be used to upload IL0 firmware to the Internal or external firmware repository.

A custom SPP iso Image must be created with the new IL0 firmware version and uploaded to the repository.

An external repository must be created, because standalone components are supported only In an external repository.

ILO firmware can be marked as a hotnx and uploaded directly to the Internal or external firmware repository.

Snapshot functionality will be limited only to the volumes not using these SANs.

Volume presentation through server profile will work with the discovered state.

Auto-zoning functionality will not work until SANs are associated with networks.

Volume provisioning will only work for arrays that ate accessible through these SANs.

Only HPE Synergy Compute Modules with a server profile applied.

Any Gen8, Gen9 and Gen10 servers managed using HPE OneView.

Any servers under warranty or active service contract.

Any server except HPE Superdome Flex and HPE Superdome Flex 280.

When storm control or loop protection will be enabled for Virtual Connect modules

When each of the frames has two Virtual Connect modules installed

When each Virtual Connect module is installed in different frame

When each Virtual Connect module is installed in different fabric

SCP

HTTPS

SFTP

HTTP

FTP

2 frames

4 frames

3 frames

1 frame

5 frames

This mode will suppress unwanted emails and activity alerts for routine server maintenance.

This mode will temporarily remove server profiles from the server for the maintenance period.

This mode will disable all network and storage connections during the maintenance period.

This mode will position the server in an isolated network to allow hardware or software maintenance.

Volumes created on the first storage pool cannot use data reduction technologies

Both storage pools are in a managed state and can be used for volume provisioning

HPE OneView can be used to configure volume replication between these pools

Both storage pools have a license applied that enables management of these pools

Logical Enclosure

Logical Interconnect Group

Logical Interconnect

Server Profile

deploy HPE OneView for VMware vCenter Server

deploy HPE OneView Global Dashboard

use an Ansible playbook

integrate all HPE OneView appliances and HPE Composers with Active Directory

reset an il_0 management processor to activate the new boot mode for the server

reinstall an operating system, as UEFI is using different drive format than Legacy BIOS

reset BIOS settings to the defaults so UEFI settings can be applied

reset BIOS settings to the defaults through the server profile after changing the boot mode

whether WSAPI service is enabled on HPE Primera array.

whether the appropriate license for HPE Primera Is available in HPE OneView.

whether array management using HPE OneView is enabled in SSMC.

whether there are at least two Fibre Channel networks defined in HPE OneView.

SFTP

NFS

FTP

CIFS

A logical JBOD lifecycle can be associated with a server profile lifecycle and drives can be securely erased.

A logical JBOD cannot be created during server profile creation and must be prepared in advance

Different types of the drives can be used within a logical JBOD as long as they have the same capacity

Logical JBOD functionality must be enabled on the Enclosure Group level by a storage administrator

Boot volumes can be created on demand and defined in the server profile template.

Boot volumes can be prepared in advance and later presented as shared volumes to the Compute Modules.

An existing volume can be replicated automatically when creating a server profile.

single SAN volume can be created and utilized by all HPE Synergy Compute Modules.

Customer has to use HPE OneView server migration feature to migrate new servers to an existing logical enclosure.

Customer has to create new enclosure group and re-parent an existing logical enclosure to the new enclosure group.

Customer has to join new enclosure to the management ring and modify logical interconnect group to add new frame.

Customer has to delete an existing logical enclosure, create new enclosure group and re-create logical enclosure.

State of the SAN connections in the server profile.

FC network definition and association with fabrics from SAN manager.

Consistency checking level for SAN storage in the server profile.

Proper array and storage pools licensing in HPE OneView.